ARC – A10 Touring Competition Car Carbon Chassis 1:10 (På lager!)

kr 6.799.00

4 på lager

Varenummer: AC-R100032 Kategori:


ARC – A10 Touring Competition Car Carbon Chassis 1:10

May be an image of text that says 'ARC A1O dvancedRCC DRIC The A10 it's ready ARC's latest generation 1/10 lectric touring car and h itt”e rack! Built on completely new platforn A10 was developed with some goals mind lower center gravity, increased mechanical grip, easy maintainance & setup and ull adjustability Key new features of ARC's are listed below.......'

May be an image of text that says 'A10 Flex control screw ×3 Ball bearing Flex control screw NEW UPPER DECK Featuring a new one-piece upper deck, the A10 is super easy to drive out-of-the-box and suits wide range of track conditions. An optional two-piece design is available to independently tune the front and rear flex for racers looking to get the most out of their A10. There are 3pcs flex screw in front end and 2pcs flex screw in rear, more flex screw mount on the upper deck will make less flex.'

May be an image of text that says 'A1O ALL-NEW ONE-PIECE MOTOR BULKHEAD The new one-piece motor bulkhead caters for both upper deck designs, allowing different flex options via both the chassis and top decks. The bottom of the motor bulkhead now also features a 3mm center alignment pin to better locate the chassis when less chassis screws are used. This allows extra chassis flex to be dialed in with less likelihood of tweaking.'

May be an image of text that says 'A10 FULL CARBON LOW ARMS The brand-new lower arms of the A10 are made from 3mm thick, high-quality carbon fiber plate and are stronger and lighter than traditional composite arms The design of the new lower arms allows the arms to be moved further inboard for an even longer arm than the R12. Back-to-back testing has confirmed this new design be even easier to drive while achieving greater corner speed.'


No photo description available.

May be an image of text that says 'A10 BODY STOP UPPER ARM The upper arm now incorporates mounting points for adjustable body stops. This allows the simple of use of a screw to act as a body stop. Using this allows the height of the body to be lowered while preventing the front tires from touching the wheel arches during cornering. This improves the handling characteristics of the car during hard cornering and aids aerodynamic performance.'

May be an image of text that says 'A10 LOW FRICTION BALL JOINTS All ball joints on the A10 are now using ARC's low friction ball ends. These provide smoother operation with less wear and slop between the ball joints and balls.'

May be an image of text that says 'A1O 00 ATS SYSTEM The A10's rear suspension system now features an integrated the Active Toe System (ATS) This system allows the rear toe angle vary during suspension travel, for further ease tuning. By varying the angle the ATS linkage, the amount of rear tow gain loss can be varied to suit your driving style and track conditions. The default setup increases rear toe during suspension travel. This further improves traction and corner speed with improved tire wear.'

May be an image of text that says 'A10 Pg BANDO lon HORIZONTAL BODY POST The optional horizontal body post helps to lower the rear center gravity, while the extended rear body tower can also reduce the body deflection bend during impact. This setup results in slightly reduced rear downforce which can deliver increased corner speed under certain conditions.'

May be an image of text that says 'A1O 0 0.75 CASTER GAUGE INCLUDED ARC's bespoke caster gauge is included with every A10 kit. The caster gauge can be adjusted to suit most setup stations that are available on the market today.'

May be an image of text that says 'A10 EASY ACCESS SPUR The spur adaptor on the A10 is mounted on one side of the motor bulkhead, allowing easy access to the spur and belts. This allows for simple maintenance and spur replacement without removing upper deck and motor bulkhead.'

May be an image of text that says 'A10 አንስልg Gpo0 KA S LiPa 6000 BATTERY HOLDER INCLUDED The included carbon fiber battery holder suits both standard and shorty LiPo batteries, with two corresponding sets of holes on the chassis for both types of batteries. Racers can either fasten the battery with tape or use the included adjustable battery retaining tab.'



Det er ingen omtaler ennå.

Bli den første til å omtale “ARC – A10 Touring Competition Car Carbon Chassis 1:10 (På lager!)”

Din e-postadresse vil ikke bli publisert.

Dette nettstedet bruker Akismet for å redusere spam. Lær om hvordan dine kommentar-data prosesseres.

Product files

  1. R12 Instruction Manual (pdf)
  2. R12 Setupsheet Default (pdf)
  3. R12 Setupsheet Editable (pdf)